How to Seam Solid Surface

Tools Required

Adhesive & Gun 

Clamp Blocks

Glue Gun



Denatured Alcohol

Seaming using Clamp Blocks

1. Before any seaming technique, it is wise to dry fit the pieces together to confirm you have straight seamable edges. Position the material next to each other and push the seamed edges together. You should see the seam almost disappear. If you see any gaps or chips, you will need to use a trim router and straight edge to clean and straighten you seam edge. Once your dry fit test looks good, pull your material apart slightly and proceed to the next step.

confirming the edges of the solid surface are clean before seaming process

Confirm Edges Are Clean

doing a dry fit of the solid surface pieces before seaming process

Dry Fit Pieces

2. Wipe the area clean with denatured alcohol. Using a hot glue gun, attach clamp blocks on either side of your seam. There should always be a minimum of three clamp blocks (one on both ends and one in the center). For larger seams (greater than 30”) it is recommended to add additional blocks such that there is a clamp block at least every 10” along the seam.

wiping the edges of the solid surface with denatured alcohol before seaming the material together

Wipe with Denatured Alcohol

using a hot glue gun to attach clamp blocks on either side of where the seam is

Hot Glue Clamp Blocks

Key Tip: Don't worry about the hot glue on your solid surface. You can easily chisel it off and clean with denatured alcohol.  

3. Place a strip of tape face down underneath the seam spanning the two sheets. This tape will keep the glue off the table and keep your material from adhering to your work surface. Wipe your seam edges with denatured alcohol to ensure they are free of all debris.

taping underneath the solid surface where the seam is located

Tape Below Seam

Wiping the edges of the seam with denatured alcohol to ensure they are free of debris before seaming pieces of material together

Wipe Down Edges

image of the seam with tape underneath, and wiped free of debris ready to be seamed together

Ready to Seam

4. Using your adhesive dispensing gun and mixing tips, dispense 5-10 inches of adhesive onto a piece of cardboard or scrap. Note the below image showing the visible difference in adhesive consistency once properly mixed. This step is critical as it ensures the two-part adhesive is properly mixed. If ignored, your adhesive will not cure.

testing the adhesive gun to ensure the adhesive is properly dispensing

Confirm Adhesive Dispenses Properly

dispensing adhesive on piece of cardboard to ensure the mixture of adhesive is correct

Test Dispense to Ensure Mixture

5. Apply ¼” diameter beads of glue along each seam face in turn. It is recommended to place the adhesive near the top of the first edge. This minimizes adhesive drip off the material while you apply adhesive to the other edge. It is important to apply adhesive to both edges. This ensures you aren’t light on the adhesive (or adhesive activator) in one section of the seam.

applying the adhesive to the seam

Apply Adhesive

applying a consistent amount of adhesive down the full seam

Apply Consistent Bead Down Full Seam

applying adhesive to both sides of material

Apply Adhesive to Both Sides at Top

6. Press the two material pieces together and tighten down your clamp across the blocks. You will have some excess adhesive that is pushed up out of the seam. This "squeeze out" should be relatively consistent across the seam. You will also need to clamp down the other edges of your material to keep the sheet from trying to fold up on the seam. 

pressing the material together and tightening clamps

Tighten Clamps

clamping the ends of the material

Clamp Ends of the Sheet

Key Tip: Take care not to overtighten as this will cause too much adhesive to be expelled and can cause a weaker seam. 

Key Tip: Once clamped, run your finger over the glue and squeeze it out in a few places across the seam to check that the material is still level. If one side has risen, put pressure/tap the proud side to press the material back to level before walking away and allowing it to cure.

7. After 45 minutes, remove clamps, knock off the clamp blocks and scrap excess glue off with a chisel.

removing the clamp blocks from the material

Remove Clamp Blocks

scraping excess glue off with a chisel

Chisel Excess Glue

8. Using an orbital sander, sand away the excess glue. Start with 80-micron pads, feathering out to each side roughly 4-6 inches. Next, upgrade to 60-micron pads and sand out roughly 10-12 inches. At this point, the seam itself should be nearly invisible. 

using an orbital sander to sand down excess glue
using orbital sander to sand away excess glue
using orbital sander to sand away excess glue
after sanding the material, the finished seam should be nearly invisible

Key Tip: The seaming process almost always occurs before your final polishing of the countertop surface. Because of this it is generally not critical to perfectly feather and blend the seam at this stage. Your goal at this point is primarily knocking off the glue line. The first step of the polishing process will be to sand to a uniform finish. You then use a sandpaper progression to polish to the desired finish. Once this is completed your material will be effectively "seamless".

Adding Seam Blocks

For structural integrity, it is wise to add a 2-3” wide seam block underneath the seam on the bottom of the countertop. Seam blocks are added after any edge buildup strips are added so that you know the appropriate length of the seam block. 

1. Measure the space between your edge finishing along your seam. Cut your seam block leaving 1/8" gap between the seam block and your edge buildups.

2. Center the seam block on your seam. Hot glue stop blocks on either side

locating the seam block

Step 1: Locate Seam Block

centering the seam block on the seam and applying hot glue to the block

Step 2: Hot Glue Stop Blocks

3. Liberally apply adhesive to the underside of the seam block. Press into place between the recently added stop blocks. 

applying adhesive to the underside of the seam block

Apply Adhesive

pressing the seam block into place between the added stop blocks

Press into Place

4. Clamp on either end of the stop block and in the center add a weighted item while the seam block cures.

clamping the end of the block and adding a weighted item while the seam block cures

Clamp and Let Cure

Note: Solid Surface fabrication manuals traditionally recommended cutting angles along the edges of the seam block (typical to the above pictures). Many industry professionals still do this out of habit however the newest fabrication manuals now do not require this step.

Additional Seaming Notes

Seam Expectations - Not all solid surface colors seam as easy as others. Solids and colors with smaller particulates are easily seamed such that even the most trained eye can't spot the seam. Conversely, very large particulate patterns and patterns with grain directions are generally much harder to make appear “seamless”.

Do Not Try to Seam Factory Edges - You should never try to seam an edge directly as it is delivered from the manufacturer. The reason being is the material has been handled and it is unlikely that the edge is smooth enough to be properly seamed. You must make one pass with a hand router to clean the edge before attempting a seam. View our article "Cutting Solid Surface" for more information.

Professional Tools - There are many sophisticated tools available for high volume production seaming of solid surface material. Some serve the simple purpose of holding the material together while the glue cures. Others help auto-level the material which helps you avoid extra sanding post seaming.

While these tools are convenient, they are certainly not required. This is especially true for a single DIY solid surface project. Using simple clamp blocks and clamps (as described above) is a tried and true method used successfully on thousands of countertops.

Additional Resources